ESP32-Devkitc-v4
一、arduino-esp32
Arduino core for the ESP32, ESP32-S2 and ESP32-C3 是乐鑫官方为ESP32提供的Arduino内核引擎。
开源仓库地址: Arduino core for the ESP32, ESP32-S2 and ESP32-C3。在线文档地址:Getting Started。
目前支持以下ESP32系列:
Arduino Reference:/reference/en/。
二、借助Arudio IDE 安装Arduino-ESP32
1. 安装Arduino IDE
下载地址:/en/software。
下载之后解压即可。
2. 安装Arduino-ESP32
打开 Arduino IDE 首选项:
在【附加开发板管理器网址】中填入url:
稳定版发布链接:
/espressif/arduino-esp32/gh-pages/package_esp32_index.json
开发板发布链接:
/espressif/arduino-esp32/gh-pages/package_esp32_dev_index.json
这里我选择稳定版:
打开【工具】【开发板管理器】,安装esp32平台:
这里需要自己处理一下网络,你懂的,否则连json文件都拉不到。(点这里)
安装之后在开发板可以看到,选择ESP32-C3F开发板:
安装完成,重启Arduino IDE。
三、HelloWorld
1. 导入示例
ESP32-Arduino库中带了很多示例,这里以获取芯片ID为例:
2. 示例代码
/* The true ESP32 chip ID is essentially its MAC address.This sketch provides an alternate chip ID that matches the output of the ESP.getChipId() function on ESP8266 (i.e. a 32-bit integer matching the last 3 bytes of the MAC address. This is less unique than the MAC address chip ID, but is helpful when you need an identifier that can be no more than a 32-bit integer (like for switch...case).created -06-07 by cweinhoferwith help from Cicicok */uint32_t chipId = 0;void setup() {Serial.begin(115200);}void loop() {for(int i=0; i<17; i=i+8) {chipId |= ((ESP.getEfuseMac() >> (40 - i)) & 0xff) << i;}Serial.printf("ESP32 Chip model = %s Rev %d\n", ESP.getChipModel(), ESP.getChipRevision());Serial.printf("This chip has %d cores\n", ESP.getChipCores());Serial.print("Chip ID: "); Serial.println(chipId);delay(3000);}
不得不说,这玩意的代码是真简洁。
3. 编译
4. 下载
选择开发板连接的串口:
点击下载(Arduino中叫上传):
5. 串口监视器
打开串口监视器,即可看到ESP32输出的日志:
四、借助 PlatformIO 安装Arduino-ESP32
1. 安装PlatformIO(PIO)
打开VS Code,搜索platformio ide
扩展,安装扩展:
2. 快速开始
(1)点击底部状态栏的【PlatformIO Home】按钮:
(2)点击【New Project】,选择开发板并创建一个新的PlatformIO项目:
第一次新建工程会比较久:
工程创建完成后,如图:
(3)编写测试代码:
#include <Arduino.h>void setup(){Serial.begin(115200);}void loop(){Serial.println("Hello World");delay(1000);}
3. 编译下载
(1)点击编译按钮,编译代码
(2)点击上传按钮,上传代码
4. 串口终端
PlatformIO自带的串口Monitor太难用了,还是串口助手香: