晶化速率,crystallization velocity
1)crystallization velocity晶化速率
1.A series of contrast DSC experiments of the originality and treated amorphous Fe 73 5 Cu 1Nb 3Si 13 5 B 9 alloys annealed at 520℃ and with shock wave technique treatment were made Thecrystallization velocity of the treated samples above are mainly summed up and discussed by combined crystallization mechanis着重结合晶化机理对样品在上述处理中的晶化速率作了对比和讨论。
2)crystallization rate结晶速率
1.The results show that nonisotheramal crystallization results are successfully analyzed by Mo Zhishen theory,and thecrystallization rate of mLLDPE is slo- wer than that of traditional LLDPE at the same relative crystallinity.结果表明,采用莫志深法处理数据可得到较好的线性关系,且mLLDPE在相同的相对结晶度下的结晶速率低于LLDPE。
2.A kind of PET/GF composite with good mechanical properties and rapidcrystallization rate was prepared.制备了结晶速率快、力学性能优异的玻纤增强聚对苯二甲酸乙二酯(PET/GF)。
3.Thecrystallization rate and the relative crystallization degree of PP/Talc composites is higher than those of pure PP, which causes the change of growing way for crystal nucleus and is advantageous to the processing and properties for PP/Talc composites.用差示扫描量热法(DSC)研究聚丙烯(PP)及PP/Talc复合材料的非等温结晶过程,加入滑石粉后,PP/Talc的结晶速率、结晶度得到明显提高。
英文短句/例句
1.Based on the crystal growth elementary principle,a plagioclase crystalline velocity equation is suggested.从晶体生长的基本原理出发，提出了按非连续机制生长的斜长石晶体结晶速率表达式。
2.The nucleation and growth rate equations of DSP were determined by non-linear regression analysis.确定了反应结晶和溶析结晶过程中晶体成核和生长速率方程。
3.At first a comprehensive and short review on the characteristics for size growth-rate of crystals is presented.首先对微晶粒尺寸增长速率的表征进行总结.
4.Strategic Study on Batch Iso-electronic Crystallization of Glutamic Acid Ⅰ Rate of Neutralizing Acid谷氨酸间歇等电结晶研究Ⅰ:调酸速率的控制
5.Effect of strain rate on dynamic recrystallization microstructures of β hot process for TA15 titanium alloy应变速率对TA15钛合金β热变形动态再结晶组织的影响
6.In films Sb could act as the nucleation center and speed up the rate of crystalliza-tion.在薄膜中,Sb 起着晶核作用,加快析晶速率。
7.Relationship of Cooling Rate and Grain Sizes in ZL205A Alloy;ZL205A合金冷却速率与晶粒度的关系
8.Study on MacPherson-Srolovitz"s grain growth rate equation with Monte Carlo simulationMacPherson-Srolovitz晶粒长大速率方程的仿真验证
9.Study on the Release Rate of Latent Heat in Solar Grade Czochralski Silicon Growth;太阳能硅单晶快速生长中结晶潜热的研究
10.Influence of Increasing Casting Speed of Hypoperitectic Steel Slab on Heat Transfer of Mold提高亚包晶钢板坯拉速对结晶器传热的影响
11.The growth rate can exceed the pull rate and even be negative at a given time.生长速率可能大于拉晶速率，甚至某一时刻是负值。
12.Undercooling, Grain Refinement and Dendrite Growth Velocity in Cu-Ge Melt Alloys铜锗合金的深过冷、枝晶生长速率及晶粒细化研究
13.EFFECTS OF WITHDRAWAL RATE ON MICROSTRUCTURE AND STRESS RUPTURE PROPERTIES OF A Ni_3Al-BASED SINGLE CRYSTAL SUPERALLOY IC6SX拉晶速率对Ni_3Al基单晶合金IC6SX凝固组织和高温持久性能的影响
14.The higher temperature, the greater the reaction rate.反应温度愈高,晶核生长的反应速率愈快。
15.Grain size had some effect on the rate of crack propagation.晶粒尺寸大小对裂纹扩展速率也有影响。
16.Influence of Strain Rate on Grain Refinement by Plastic Deforming;应变速率对强塑性变形晶粒细化的影响
17.A GRAIN GROWTH RATE EQUATION BASED ON AVERAGE N-HEDRA MODEL一个基于平均N面体模型的晶粒长大速率方程
18.Progress of Ultrafast Low-Power Photonic Crystal All-Optical Switching超快速低功率光子晶体全光开关研究进展
相关短句/例句
crystallization rate结晶速率
1.The results show that nonisotheramal crystallization results are successfully analyzed by Mo Zhishen theory,and thecrystallization rate of mLLDPE is slo- wer than that of traditional LLDPE at the same relative crystallinity.结果表明,采用莫志深法处理数据可得到较好的线性关系,且mLLDPE在相同的相对结晶度下的结晶速率低于LLDPE。
2.A kind of PET/GF composite with good mechanical properties and rapidcrystallization rate was prepared.制备了结晶速率快、力学性能优异的玻纤增强聚对苯二甲酸乙二酯(PET/GF)。
3.Thecrystallization rate and the relative crystallization degree of PP/Talc composites is higher than those of pure PP, which causes the change of growing way for crystal nucleus and is advantageous to the processing and properties for PP/Talc composites.用差示扫描量热法(DSC)研究聚丙烯(PP)及PP/Talc复合材料的非等温结晶过程,加入滑石粉后,PP/Talc的结晶速率、结晶度得到明显提高。
3)rate of crystallization结晶速率
1.Based on the experimental results and theoretical calculation, the effects of nano silica on the crystallinity andrate of crystallization of PET were obtained.以纳米氧化硅作PET填加剂 ,实验测定及理论计算得到不同填加量对PET的结晶度及结晶速率的影响 ,表明纳米氧化硅的适宜填加量为 1 6 4 %。
4)withdrawal rate拉晶速率
1.The effects ofwithdrawal rate on liquid / solid interface morphology, primary arm spacing,precipitation behaviour of (γ+γ") eutectic and γ"particles as well as microstructure of single crystal Ni-base superalloy have been investigated.研究了拉晶速率对单晶高温合金凝固界面形态、一次臂间距、（γ＋γ＇）共晶和γ＇相析出行为的影响。
2.In the present investigation,the influence ofwithdrawal rate on the microstructure and stress rupture properties of a Ni_3Al-based single crystal superalloy IC6SX were studied.采用螺旋选晶法制备Ni_3Al基单晶合金IC6SX试棒,研究了不同拉晶速率对凝固组织和高温持久性能的影响。
5)crystallization rate晶化速度
1.Influences of the quantity of cationic surfactants on thecrystallization rate of zeolite 4A and the length of hydrocarbon chain of cationic surfactants on thecrystallization rate and particle size distributions of zeolite 4A were studied.研究了阳离子表面活性剂加入量对4A沸石晶化速度以及阳离子表面活性剂的碳氢链长对4A沸石晶化速度和粒度的影响。
2.Influences of NaCl on thecrystallization rate and the particle size distribution of zeolite 4A were studied.研究了添加无机盐氯化钠(NaCl)对4A沸石晶化速度以及粒度的影响。
6)crystalline fraction晶化率
1.The preferential growth orientation,thecrystalline fraction and the grain sizes of poly-Si films significantly depend on the filament temperature and the distance of substrate to filament.利用XRD、拉曼光谱和原子力显微镜(AFM)研究了灯丝与衬底间距(5~10mm),灯丝温度(1800~1400℃)和衬底温度(320~205℃)对薄膜晶体取向、晶化率、晶粒尺寸以及形貌的影响规律。
2.The result also shows that the stability photoconductivity of the films is related to thecrystalline fraction and the grain size of the films.实验结果表明,所制备的多晶硅薄膜具有类稳恒光电导效应,而且薄膜的稳恒光电导特性依赖于薄膜的晶化率和晶粒尺寸,随晶化率的增加和晶粒尺寸的增大而增大。
延伸阅读
多晶莫来石晶须(纤维)分子式：CAS号：性质：莫来石相为主晶相的多晶纤维。化学成分为Al2O3 72％～77％，SiO222％～17％，B2O3 3％～5％，P2O51.5％～3.0％。纤维直径2～7μm，纤维长度20～125μm。使用温度1350℃。多采用溶胶-凝胶法制造。主要用作补强填料，也可作为轻质、隔热保温材料使用。
